A solid sample material should always be sufficiently prepared by size
reduction and homogenization before it is subjected to chemical or physical analysis. Care should be taken that the analysis sample fully represents the original material and that the sample preparation process is carried out reproducibly. Only then are meaningful results guaranteed. Most sample materials can be reduced to the required analytical fineness at room temperature by choosing a mill with a suitable size reduction principle (impact, pressure, friction, shearing, cutting).
White Paper Sieve Analysis - Different methods for a variety of applications
The determination and knowledge of the particle size distribution is an essential part of the quality control process for industrial products. From incoming and production control to research and development sieve analyses are used to determine a number of parameters or simply the particle size. Easy handling, low investment cost and high accuracy make sieve analysis one of the most frequently used procedures for measuring the particle size. This white paper gives an overview of the different sieving techniques and describes the necessary steps to ensure reliable results.
White Paper: Important Aspects of Sample Preparation of Biological Materials
From cell disruption to homogenization and pulverization of a great variety of biological samples
Biological samples exist in all shapes and sizes: hard bones, tough and fibrous plants, tough and viscous sputum, soft muscles, tumor or liver tissue. Not to mention the millions of cells such as yeast, bacteria or algae, which have to be disrupted for applications such as DNA or RNA isolation or protein extraction. For research in genomics, transcriptomics or metabolomics, all kinds of biological samples are prepared. Sample preparation is the first step of every analytical process. Retsch offers a range of mills and grinders for easy and reproducible pulverization of solid sample materials some of which are also suitable for cell disruption and homogenization of biological sample materials.
White Paper: Ultrafine Grinding with Laboratory Ball Mills
How are nano particles produced? The “Bottom-Up” method synthesizes particles from atoms or molecules. The “Top-Down” method involves reducing the size of larger particles to nanoscale, for example with laboratory mills. Due to their significantly enlarged surface in relation to the volume, small particles are drawn to each other by their electrostatic charges. Nano particles are produced by colloidal grinding which involves dispersion of the particles in liquid to neutralize the surface charges. Both water and alcohol can be used as dispersion medium, depending on the sample material. Factors such as energy input and size reduction principle make ball mills the best choice for the production of nanoparticles.
Per la riduzione di dimensioni di molti materiali è consigliabile utilizzare un mulino criogenico invece di un mulino che opera a temperature ambiente. Il campione viene infragilito con l'azoto liquido che migliora il suo comportamento di rottura quando viene sottoposto a impatto, pressione e attrito. Inoltre, in questo modo vengono conservati i componenti volatili del campione. Il mulino Cryomill non solo è il mulino criogenico più sicuro e moderno sul mercato ma fornisce anche eccellenti risultati di macinazione.
Por lo general se asocia a la noción "fragmentación", el machacamiento, de sustancias sólidas mediante fuerza mecánica. Pero también la división de líquidos en gotas o de gases en bollas representa un proceso de fragmentación.
Los más precisos resultados de trituración en el más breve tiempo se consiguen con los nuevos molinos planetarios de bolas, de Retsch. Con el PM100 y el PM200, Retsch presenta una nueva generación de molinos planetarios de bolas con uno o dos unidades de trituración, que establecen nuevos estándares de rendimiento en este segmento de la producción.
El nuevo molino ultracentrífugo ZM 200 de RETSCH es un molino de rotor no sólo extremadamente rápido y cuidadoso con el material molido, sino también de uso universal gracias a su amplia gama de accesorios.
Die meisten Probenmaterialien lassen sich durch die Wahl des geeigneten Zerkleinerungsgerätes problemlos mahlen. Die Beanspruchungsmechanismen wie Prall, Druck, Scherung, Schneiden, Reibung reichen bei Raumtemperatur aus, um das Material auf die benötigte Partikelgröße zu zerkleinern. Was aber kann man tun, wenn die mechanische Beanspruchung allein nicht ausreicht, um das Probenmaterial in möglichst kleine Partikel zu überführen? Eine Lösung dieser Problematik bietet der Einsatz von Flüssigstickstoff, der das Bruchverhalten solcher Materialien begünstigt.
In zahlreichen Labors werden täglich viele unterschiedliche Probenmaterialien aufbereitet. Für die Zerkleinerung von Feststoffproben auf Analysenfeinheit wird eine Mühle benötigt, die nicht nur vielseitig einsetzbar und leicht zu reinigen ist, sondern die auch eine reproduzierbare Probenvorbereitung – und damit zuverlässige Analysenergebnisse - garantiert. Mit der Ultra-Zentrifugalmühle ZM 200 bietet RETSCH eine Rotormühle an, die nicht nur sehr schnell, sondern auch äußerst materialschonend zerkleinert und, dank einer umfangreichen Zubehörpalette, universell einsetzbar ist. Mit ihrem kraftvollen Powerdrive-Antrieb vermahlt die ZM 200 weiche bis mittelharte und faserige Materialien extrem schnell auf Endfeinheiten bis unter 100 µm und steigert so den Probendurchsatz im Labor.
Sometimes the preparation and homogenization of biological samples can be as tough as the material itself. The widely used 2 ml single-use Eppendorf tubes are often not large enough to accommodate the whole sample volume; hence, the sample needs to be divided and reunited after the homogenization process which means an additional time-consuming working step in the lab routine. While it is true that usually larger sized grinding jars, e. g. of stainless steel, are available which accommodate the complete sample volume, these have the drawback of requiring cleaning after use.
The development of drugs with poorly soluble to insoluble active ingredients is a big challenge for the pharmaceutical industry. The bioavailability of orally taken active ingredients, which means to what extent and in which period of time the substance is ingested by the body and is available at the place of action, strongly depends on the percentage dissolved in the gastrointestinal tract. One way to improve the solubility and thus the bioavailability of active ingredients is the pulverization of these substances. By minimizing the particle size to the micron and submicron range the surface-volume-ratio is increased and the solubility of the particles is improved. The pulverized particles are suitable for use in a variety of dosage forms, for example classic tablets or capsules.
Joint replacements, especially of hip and knee joints, rank among the most frequent surgical interventions in industrialized countries. One of the major risks of a joint replacement is prosthetic joint infection (PIJ), a bacterial infection at the interface of implant, tissue, and bone.
In 2010, A.-L. Roux et al. published an article titled „Diagnosis of prosthetic joint infection by beadmill processing of a periprosthetic specimen.“ It describes a new diagnosis method of involved microbes, with an impressive documentation rate of more than 83% and, at the same time, a very low contamination rate of 8.7%. The method involves washing the microbes off the tissue samples with 20 ml sterile water and 5 ml glass beads of 1 mm diameter at 30 Hz in a RETSCH
Mixer Mill within 210 seconds.
Use of laboratory grinders for size reduction of human bones and bioceramics
Bone implants and substances for bone regeneration are used in surgery to replace degenerated bone material by implants or to “re-build” it with specific substances. The material used in implants varies from autogeneic (supplied by the patient) through allogeneic (supplied by a donor) bones to replacement materials such as hydroxylapatite (HA) and tricalcium phosphate (TCP). Bovine bones and corals are used in conjunction with synthetically produced foamed materials to form a basis for the regeneration of bone substance. Various RETSCH mills are suitable for the preliminary and fine grinding of human bones as well as bioceramic materials.
In the analysis of solid material, the popular adage that “bigger is better” certainly does not apply. The goal is to produce particles that are sufficiently small to satisfy the requirements of the analysis while ensuring that the final sample accurately represents the original material. The “particles” of interest to the analyst generally range from 10 µm to 2mm. Additionally there are many application, where even finer sizes are needed. One example are active ingredients, where it is necessary to grind in the submicron range. Finally for DNA or RNA extraction mechanical cell lysis is well-established.
Materials differ widely in their composition and physical properties. Hence, there are many different grinding principles that can be applied, and this, together with other variables such as initial feed or “lump” size, fineness needed and amount of sample available, results in a wide range of models available to the researcher.
A faultless and comparable analysis is closely linked to an accurate sample handling. Only a sample representative of the initial material can provide meaningful analysis results. Rotating dividers and rotary tube dividers are an important means to ensure the representativeness of a sample and thus the reproducibility of the analysis. Correct sample handling consequently minimizes the probability of a production stop due to incorrect analysis results. Thus correct sample handling is the key to effective quality control.
Some sample materials have properties which make size reduction at ambient temperature impossible. If, for example, very elastic materials need to be ground or volatile components have to be preserved for further analysis, it is essential to carry out cryogenic grinding. The use of liquid nitrogen helps to embrittle the sample, thus improving its breaking properties, and preventing volatile substances from escaping due to the frictional heat produced by the grinding process.
The SM 300 excels especially in the tough jobs where other cutting mills fail. It has a freely selectable speed range from 700 to 3,000 rpm with high torque. The mill is convenient to operate and easy to clean. Reliable and extremely efficient sample preparation in the laboratory is now guaranteed with the SM 300.
The detection of illegal drugs and pharmaceuticals plays a role in various fields, for example in forensic science, road traffic accidents, in competitive sports or at the workplace. Chemical substances can be detected in blood, saliva, urine and in hair. Hair has the great advantage of storing the substances for a long period, which means that detection is still possible several months after consumption of the drug. In addition to the detection of drugs, hair samples are also used for DNA analysis as well as for the analysis of heavy metals and minerals.
The following situation is typical for many production plants: After a routine quality check, the production process is stopped or an already produced batch is suspended, because the analysis results were not within the relevant critical values. But does the tested product really deviate from the specifications? The quality control managers are convinced of this because modern analysis instruments provide results with very low tolerances. The sample in question was tested several times and the result was confirmed. The question is why the product does not match the specifications although the production parameters have not been changed in any way. The possibility that the tested product is indeed deficient cannot be excluded. However, it is often not the product itself which causes irregular analysis results but a lack of understanding of the steps which come before the analysis.
Particle size analysis and particle size distribution are important criteria for the quality control of bulk materials. In a running production process, the results of a quality check must be available quickly to allow for immediate adjustment of the production parameters. Depending on the expected particle size and sample volume, different sieving methods and sieving machines are suitable for analysis. The method used for particle size analysis is primarily determined by the fineness of the material to be sieved. For dry sieving of samples with particle sizes below 40 microns, air jet sieving is the method of choice.
Рекомендации пользователей (2)
Криогенное разруше- ние дрожжевых клеток - Rockefeller University, USA